HULL SECTION,MIDGET SUBMARINE,MI

2040FSC

01NCB code

701-4331Item number

NIIN 01-701-4331

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	Z	SMS	EA	0.0000	$1,505.85	1	U	0	9B-----	$0.00	N
01-OCT-2026	DS	Z	SMS	EA	0.0000	$1,505.85	1	U	0	-------	$0.00	I

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC
245-7383869	53711 NAVAL SEA SYSTEMS COMMAND	A	D	9	D	ZZ
245-7383869-35	53711 NAVAL SEA SYSTEMS COMMAND	A	3	2	D	ZZ
26M01-4303-35	96169 ELECTRIC BOAT CORPORATION DIV GENERAL DYNAMICS ELECTRIC BOAT	A	5	1	5	ZZ

END ITEM IDENTIFICATION	NSSN CLASS PROPULSOR INCOMPRESSIBLE WEDGE
PART NAME ASSIGNED BY CONTROLLING AGENCY	WEDGE, INCOMPRESSIBLE, CONDUIT LEADING FAIRING
SPECIAL FEATURES	THE MAXIMUM STEP DROP, GAP ALLOWANCES AT THE OUTSIDE DIAMETER OF THE PROPULSOR SHALL BE: STEPS: 0.025"; DROPS: 0.050"; GAPS: 0.125"; PORT AND STARBOARD EDGES SHALL BE FLUSH TO WITHIN + OR - 0.050" OF ADJACENT STRUCTURE AREAS NOT CONFORMING TO THESE STEP, DROP; GAP ALLOWANCES MUST BE FAIRED IN WITH AN APPROVED, INCOMPRESSIBLE WEDGE MATERIAL OR APPROVED FAIRING COMPOUND; UNLESS OTHERWISE SPECIFIED ALL TAPERS OF INCOMPRESSIBLE WEDGES AND FAIRINGS FACING PORT AND STARBOARD SHALL BE BLENDED INTO THEIR CORRESPONDING 6 TO 1 MINIMUM TAPERS; WHEN 2 OR MORE TAPERS MEET OR INTERSECT, THE ANGLE INCLUDED BETWEEN THE TAPERS OF THE INTERSECTING WEDGES OR FAIRINGS SHALL BE NO LESS THAN THE ANGLE INCLUDED BETWEEN THE TAPER OF A STAND ALONE WEDGE OR FAIRING AT THE OUTSIDE DIAMETER OF THE PROPULSOR
PROPRIETARY CHARACTERISTICS	PACS
SUPPLEMENTARY FEATURES	HULL SECTION

PICA SICA: P
PKG cat: 18ZA
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: B
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 10
Physical protection
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: CA
A-A-203, kraft wrapping paper
Cush dun: JC
ASTM D4727/D4727M, domestic fiberboard used as pads, cells, die cuts or sleeves
THK: C
3/4 inch thick
Unit cont: NO
ASTM-D5118/D5118M, Type CF, Class weather resistant, double wall, corrugated fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: E5
ASTM D5118/D5118M, fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: ZZ - SPECIAL MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.