ROTOR,COMPRESSOR,AIRCRAFT GAS TU

2840FSC

01NCB code

713-5094Item number

NIIN 01-713-5094

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	Z	SMS	EA	0.0000	$10,219.99	1	9	0	9B-----	$0.00	N
01-OCT-2026	DS	Z	SMS	EA	0.0000	$10,219.99	1	9	0	-------	$0.00	I

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC
5140T34	99207 GENERAL ELECTRIC COMPANY DBA GE AEROSPACE	A	D	9	D	ZZ
5140T34P01	99207 GENERAL ELECTRIC COMPANY DBA GE AEROSPACE	A	3	2	D	ZZ

OVERALL WIDTH	INCHES MINIMUM 0.545 AND INCHES MAXIMUM 0.548
END ITEM IDENTIFICATION	T408-GE-400 ENGINE
PART NAME ASSIGNED BY CONTROLLING AGENCY	SPOILER, VORTEX - COMPRESSOR ROTOR
ENGINE SECTION LOCATION	COMPRESSOR
SPECIAL FEATURES	MARK IN ZONE M PER METHOD 2F2 OR 8A PART IDENT, MFR IDENT, AND SERIAL NO. MARKING METHOD SHALL NOT EXTEND PAST TANGENCY POINT N OF OF FILET. FINAL COMPONENT UNBALANCE SHALL BE LESS THAN 1.0 GRAM INCH WHEN ROTATED ABOUT AN AXIS ESTABLISHED BY DATUM A. BALANCE CORRECTIONS TO BE MADE BY MATERIAL REMOVAL AS SHOWN IN VIWE J. MULTIPLE BALANCE SLOTS ALLOWED TO ACHIEVE FINAL BALANCE REQUIREMNT. ALL BALANCE SLOTS SHALL BE THRU CUTS CONNECTING ADJACENT RADIAL HOLES. SHOT PEEN AFTER FLUORESCENT PENETRANT INSPECTION PER P11TF8 CL-A AS FOLLOWS: A. PEEN ENTIRE PART. B. USE S-70 OR S-110 STEEL SHOT. C. INTENSITY SHALL BE 0.006-0.012N. D. INTENSITY VERIFICATION REQUIRED AT LOCATION IDENTIFIED BY LOCATION L USING SCRAP PART OF SIMULATIVE FIXTURE. E. UNLESS OTHERWISE SPECIFIED, BREAK EDGES PER P1TF101 BEFORE PEENING. F. AFTER PEENING, RABBET DIAMETER K MAY BE REMACHINED WITHOUT REPEENING PROVIDED NO MATERIAL IS REMOVED FROM FILLET CURVATURE. 5. FLUORESCENT PENETRANT INSPEC PER P3TF47
MATERIAL	OVERALL IRON ALLOY 660
MATERIAL DOCUMENT AND CLASSIFICATION	OVERALL ASSN STD SINGLE MATERIAL RESPONSE A286
PROPRIETARY CHARACTERISTICS	PACS

PICA SICA: P
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: B
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 10
Physical protection
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: 00
No requirement
Cush dun: NA
PPP-C-795, closed cell plastic cushioning; or A-A-3129, open cell plastic cushioning; or PPP-C-1797, polypropylene...
THK: C
3/4 inch thick
Unit cont: E5
ASTM D5118/D5118M, fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: E5
ASTM D5118/D5118M, fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: O
Options can be exercised as to specific method of preservation or DoD approved packaging materials to be used.

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.