BEARING,PLAIN,SELF-ALIGNING

3120FSC

01NCB code

145-0550Item number

NIIN 01-145-0550

Identification

BORE DIAMETER	INCHES MINIMUM 0.8745 AND INCHES MAXIMUM 0.8750
OUTER MEMBER OUTSIDE DIAMETER	INCHES MINIMUM 1.6245 AND INCHES MAXIMUM 1.6250
OUTER MEMBER WIDTH	INCHES MINIMUM 0.7500 AND INCHES MAXIMUM 0.7600
INNER MEMBER WIDTH	INCHES MINIMUM 0.8700 AND INCHES MAXIMUM 0.8750
STATIC RADIAL LOAD RATING	POUNDS 72500
HARDNESS RATING	OUTER RACE MEMBER ROCKWELL C MINIMUM 38.0 AND ROCKWELL C MAXIMUM 37.0
LUBRICATION FEATURE	RACE LINER SELF-LUBRICATING LINER
MATERIAL	OUTER RACE MEMBER STEEL COMP 630
MATERIAL	INNER MEMBER TITANIUM ALLOY UNS R56400
MATERIAL	RACE LINER PLASTIC POLYTETRAFLUOROETHYLENE
MATERIAL DOCUMENT AND CLASSIFICATION	INNER MEMBER ASSN STD SINGLE MATERIAL RESPONSE A-S 4967 OR ASSN STD SINGLE MATERIAL RESPONSE A-S 4928
MATERIAL DOCUMENT AND CLASSIFICATION	RACE LINER MFR REF SINGLE MATERIAL RESPONSE KARON V,FSC- 50632
MATERIAL DOCUMENT AND CLASSIFICATION	OUTER RACE MEMBER ASSN STD SINGLE MATERIAL RESPONSE A-S 5643
SURFACE TREATMENT	OUTER RACE MEMBER PASSIVATE
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION	OUTER RACE MEMBER FED SPEC SINGLE TREATMENT RESPONSE QQ--35
STYLE DESIGNATOR
TEST DATA DOCUMENT	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-S-271

PICA SICA: P
PKG cat: 27A0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 41
Watervaporproof bag, heat sealed
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: ZZ
Special requirement – See specific instructions or drawings provided.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: PRESERVATION, PACKAGING, P

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.