TUBE ASSEMBLY SET,METALLIC

4710FSC

01NCB code

568-3883Item number

NIIN 01-568-3883

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	J	SMS	EA	0.0000	$90.93	1	U	0	9B-----	$0.00	N
01-OCT-2026	DS	J	SMS	EA	0.0000	$90.93	1	U	0	-------	$0.00	I

END ITEM IDENTIFICATION	7386195 (53711) PROPULSION SCTN HYD INTERCONNECT
PART NAME ASSIGNED BY CONTROLLING AGENCY	TUBE ASSEMBLY -04
SPECIAL FEATURES	PROP SEC HYD. ELECTRO-CHEMICAL ETCH IN ACCORDANCE WITH MIL-STD-130. TUBE END SHALL CONFORM TO SAE J1453 WITH THE FOLLOWING AMMENDMENTS: PROCESS INDUCED CIRCUMFERENTIAL WITNESS MARKS ARE ALLOWABLE ON THE FACE OF THE TUBE END PROVIDED THE INTEGRITY OF THE SEALING SURFACE IS NOT COMPROMISED, PROCESS INDUCED BULGING, DEFINED AS THE LOCAL SWELLING OF THE TUBE DIAMETER BEHIND THE TUBE SLEEVE, SHALL BE NO GREATER THAN .015 INCHES OVER THE ACTUAL TUBE OUTER DIAMETER. IMERSE AND FLUSH EACH TUBE OR HOSE ASSEMBLY WITH SAFETY-KLEEN PREMIUM SOLVENT OR THE EQUIVILANT, (SAFETY-KLEEN PREMIUM SOLVENT IS CAGE 0S0J2, P/N 6605. BLOW DRY NITROGEN TO DRY. REMOVE REMAINING PARTICLES FROM TUBE OR HOSE ASSEMBLY USING PNEUMATIC GUN AND POLYURETHANE FOAM PROJECTILE. OPENINGS SHALL BE CAPPED AND SEALED AIR TIGHT IMMEDIATELY AFTER CLEANING, PROCESS CAPS WITH THE SAME GRADE OF CLEANLINESS. PLASTIC TAPE IS ALLOWED TO HOLD CAPS, HOWEVER THE USE OF TAPE AS A CAP IS PROHIBITED

PICA SICA: P
PKG cat: 60Z0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: A
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: AE
Seal or plug all openings and preserve by Method 10.
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: 00
No requirement
Cush dun: NA
PPP-C-795, closed cell plastic cushioning; or A-A-3129, open cell plastic cushioning; or PPP-C-1797, polypropylene...
THK: C
3/4 inch thick
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: E5
ASTM D5118/D5118M, fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 8.50000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: O
Options can be exercised as to specific method of preservation or DoD approved packaging materials to be used.

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.