HOSE ASSEMBLY,NONMETALLIC

4720FSC

01NCB code

032-7374Item number

NIIN 01-032-7374

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNFC	RNSC	SADC
F3020639-16-16-16-92.00	87373 PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV HOSE PRODUCTS DIVISION	A	5	2	5	ZZ
3010639-16-16-1	87373 PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV HOSE PRODUCTS DIVISION	A	C	1	6	ZZ			AC
3010639-16-16-16-92.00	87373 PARKER-HANNIFIN CORPORATION DBA PNEUTRONICS DIV HOSE PRODUCTS DIVISION	A	5	2	5	ZZ
3010639-16-16-16-92.00	98441 PARKER HANNIFIN CORP	A	5	9	3	AX		B
3010639-16-16-16-92	98441 PARKER HANNIFIN CORP	A	5	9	3	AX		B
7709	04953 EDO AIL SYSTEMS INC	H	D	9	1	AX	1	B
7727PC14	04953 EDO AIL SYSTEMS INC	H	5	9	3	AX	1	B
7709-1	04953 EDO AIL SYSTEMS INC	H	3	9	1	AX	1	A

CROSS-SECTIONAL SHAPE STYLE
THREAD CLASS	2B
THREAD DIRECTION	FIRST END RIGHT-HAND
THREAD DIRECTION	SECOND END RIGHT-HAND
INSIDE DIAMETER	INCHES NOMINAL 1.000
TEMP RATING	SINGLE RESPONSE FAHRENHEIT -40.0 AND FAHRENHEIT 250.0
OUTSIDE DIAMETER	INCHES NOMINAL 1.500
MINIMUM INSIDE BENDING RADIUS	INCHES 12.000
CONNECTION STYLE
END CONNECTION DESIGN	SECOND END ELBOW
END CONNECTION DESIGN	FIRST END STRAIGHT
CONNECTION TYPE	SECOND END THREADED INTERNAL TUBE
CONNECTION TYPE	FIRST END THREADED INTERNAL TUBE
FEATURES PROVIDED	NONSKIVE AND REUSABLE END FITTINGS
THREAD QUANTITY PER INCH	12
BURST TEST PRESSURE	POUNDS PER SQUARE INCH 8000.0
NOMINAL THREAD SIZE	FIRST END INCHES 1.312
NOMINAL THREAD SIZE	SECOND END INCHES 1.312
OPERATING PRESSURE	LOCATION NOT OTHERWISE SPECIFIED POUNDS PER SQUARE INCH (PSI) MAXIMUM 2000.0
SEAT ANGLE	FIRST END DEGREES 37.0
SEAT ANGLE	SECOND END DEGREES 37.0
HYDROSTATIC TEST PRESSURE	POUNDS PER SQUARE INCH 4000.0
FLOW ANGLE	SECOND END DEGREES 90.0
OUTER COVERING ENVIRONMENTAL PROTECTION	ABRASION RESISTANT AND OIL RESISTANT AND WEATHERPROOF
INSIDE SURFACE CONDITION	SMOOTH
MEASURING METHOD AND LENGTH	INCHES NOMINAL OVERALL 92.000
MEDIA FOR WHICH DESIGNED	SINGLE RESPONSE AIR AND FUEL/OIL, HYDROCARBON AND WATER
ITEM STRUCTURAL COMPOSITION	OUTER LAYER MOLDED RUBBER, SYNTHETIC
ITEM STRUCTURAL COMPOSITION	FIRST LAYER BRAIDED STEEL WIRE
ITEM STRUCTURAL COMPOSITION	SECOND LAYER BRAIDED STEEL WIRE
THREAD SERIES DESIGNATOR	FIRST END UN
THREAD SERIES DESIGNATOR	SECOND END UN

PICA SICA: P
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: 000
No intermediate container quantity specified (000)
Method of preservation: AE
Seal or plug all openings and preserve by Method 10.
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: 00
No requirement.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 4.5000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.9260
OPI: O
Options can be exercised as to specific method of preservation or DoD approved packaging materials to be used.

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.