SCREW,CLOSE TOLERANCE

5305FSC

01NCB code

080-0683Item number

NIIN 01-080-0683

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	J	SMS	EA	0.0000	$330.30	1	U	0	9B-----	$0.00	N
01-OCT-2026	DS	J	SMS	EA	0.0000	$330.30	1	U	0	-------	$0.00	I

Part number: MS3369B314
CAGE: 96906
MILITARY STANDARDS PROMULGATED BY MILITARY DEPARTMENTS UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M
CAGE status: A
RNCC: 2
RNVC: 2
Document availability code: E
RNAAC: ZZ

THREAD DIRECTION	RIGHT-HAND
THREAD LENGTH	INCHES MINIMUM 0.262 AND INCHES MAXIMUM 0.313
FASTENER LENGTH	INCHES MINIMUM 1.247 AND INCHES MAXIMUM 1.267
HEAD STYLE
HEAD HEIGHT	INCHES MINIMUM 0.096 AND INCHES MAXIMUM 0.110
WIDTH BETWEEN FLATS	INCHES MINIMUM 0.367 AND INCHES MAXIMUM 0.376
LOCKING FEATURE	GRIP DETENT BALL
GRIP DIAMETER	INCHES MINIMUM 0.1889 AND INCHES MAXIMUM 0.1894
SHANK UNTHREADED HOLE DIAMETER	FIRST HOLE INCHES MINIMUM 0.070 AND INCHES MAXIMUM 0.080
INTERNAL DRIVE STYLE
END ITEM IDENTIFICATION	SPEC ITEM
NOMINAL THREAD DIAMETER	INCHES 0.190
GRIP LENGTH	INCHES MINIMUM 0.875 AND INCHES MAXIMUM 0.891
THREAD QUANTITY PER INCH	32
MINIMUM TENSILE STRENGTH	POUNDS PER SQUARE INCH 63000
DISTANCE FROM HEAD LARGEST BEARING SURFACE TO SHANK HOLE CENTER	FIRST HOLE INCHES MINIMUM 1.158 AND INCHES MAXIMUM 1.178
SURFACE FINISH	BEARING SURFACE OF HEAD MICROINCHES 32.0
SURFACE FINISH	GRIP MICROINCHES 32.0
MATERIAL	OVERALL STEEL COMP XM-13
MATERIAL DOCUMENT AND CLASSIFICATION	OVERALL ASSN STD SINGLE MATERIAL RESPONSE A-S 5629
SURFACE TREATMENT	OVERALL PASSIVATE
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION	OVERALL FED SPEC SINGLE TREATMENT RESPONSE QQ--35
THREAD SERIES DESIGNATOR	UNIFIED NATIONAL JOINT FINE (UNJF)

PICA SICA: P
PKG cat: 16Z0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: B
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 10
Physical protection
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: O
Options can be exercised as to specific method of preservation or DoD approved packaging materials to be used.

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.