SCREW,CLOSE TOLERANCE

5305FSC

01NCB code

359-2298Item number

NIIN 01-359-2298

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Recoverability code	Management control	Net price	USC
01-OCT-2026	DF	J	SMS	EA	0.0000	$2.71	1	U	0	N	SF9SX-N	$0.00	F
01-OCT-2026	DS	J	SMS	EA	0.0000	$2.71	1	U	0	N	-------	$0.00	I

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC
MIL-B-23964	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	4	1	4	KZ
MS3369A612	96906 MILITARY STANDARDS PROMULGATED BY MILITARY DEPARTMENTS UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	2	2	E	KZ

THREAD CLASS	3A
THREAD DIRECTION	RIGHT-HAND
THREAD LENGTH	INCHES MINIMUM 0.367 AND INCHES MAXIMUM 0.388
FASTENER LENGTH	INCHES MINIMUM 1.289 AND INCHES MAXIMUM 1.309
HEAD STYLE
HEAD HEIGHT	INCHES MINIMUM 0.126 AND INCHES MAXIMUM 0.146
WIDTH BETWEEN FLATS	INCHES MINIMUM 0.553 AND INCHES MAXIMUM 0.564
GRIP DIAMETER	INCHES MINIMUM 0.3737 AND INCHES MAXIMUM 0.3742
SHANK UNTHREADED HOLE DIAMETER	FIRST HOLE INCHES MINIMUM 0.106 AND INCHES MAXIMUM 0.116
INTERNAL DRIVE STYLE
NOMINAL THREAD DIAMETER	INCHES 0.375
GRIP LENGTH	INCHES MINIMUM 0.750 AND INCHES MAXIMUM 0.766
THREAD QUANTITY PER INCH	24
MINIMUM TENSILE STRENGTH	POUNDS PER SQUARE INCH 90000
DISTANCE FROM HEAD LARGEST BEARING SURFACE TO SHANK HOLE CENTER	FIRST HOLE INCHES MINIMUM 1.181 AND INCHES MAXIMUM 1.161
SURFACE FINISH	BEARING SURFACE OF HEAD MICROINCHES 32.0
SURFACE FINISH	GRIP MICROINCHES 32.0
SPECIAL FEATURES	TWO LOCKING BALLS OR ELEMENTS ON GRIP
MATERIAL	FASTENER IRON ALLOY 660
MATERIAL	SPRING NICKEL ALLOY 600 OR NICKEL ALLOY X-750
MATERIAL DOCUMENT AND CLASSIFICATION	FASTENER ASSN STD SINGLE MATERIAL RESPONSE A-S5737
MATERIAL DOCUMENT AND CLASSIFICATION	SPRING FED SPEC 1ST MATERIAL RESPONSE QQ-W-390 OR ASSN STD 2ND MATERIAL RESPONSE A-S5699
SURFACE TREATMENT	SPRING PASSIVATE
SURFACE TREATMENT	FASTENER PASSIVATE
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION	FASTENER FED SPEC SINGLE TREATMENT RESPONSE QQ--35
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION	SPRING FED SPEC SINGLE TREATMENT RESPONSE QQ--35
THREAD SERIES DESIGNATOR	UNIFIED NATIONAL JOINT FINE (UNJF)

PICA SICA: P
PKG cat: 27A0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: B
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 10
Physical protection
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: 00
No requirement
Cush dun: 00
No requirement
THK: 0
Not applicable
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: O
Options can be exercised as to specific method of preservation or DoD approved packaging materials to be used.

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.