PIN,STRAIGHT,HEADLESS

5315FSC

00NCB code

195-3606Item number

NIIN 00-195-3606

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC
576364-1	22525 INSTRUMENTS AND FLIGHT RESEARCH, INC.	A	5	2	5	ZZ
576364-1	94197 CURTISS-WRIGHT CORP EAST PATERSON FACILITY	R	3	9	5	ZZ
576364-1	0AHP5 CURTISS-WRIGHT CONTROLS, INC. DIV ACTUATION DIVISION	A	3	1	1	HX

FIRST END TAPER ANGLE	DEGREES NOMINAL 45.0
REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS	AS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS
FIRST HOLE DIAMETER	INCHES MINIMUM 0.062 AND INCHES MAXIMUM 0.065
FIRST END TAPER LENGTH	INCHES MINIMUM 0.015 AND INCHES MAXIMUM 0.030
PIN OVERALL DIAMETER	INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872
TEST DATA DOCUMENT	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL--23199
SECOND HOLE DIAMETER	INCHES MINIMUM 0.062 AND INCHES MAXIMUM 0.065
FIRST END STYLE
HOLE ARRANGEMENT STYLE
SPECIAL FEATURES	THIRD HOLE 0.062 IN. MIN 0.065 IN.MAX DIA LOCATED ON COMMON VERTICAL CENTER LINE BETWEEN 1ST AND SECONDHOLES APPROX 0.490 IN. FROM THE SECOND HOLE
MATERIAL	OVERALL STEEL COMP 303
MATERIAL DOCUMENT AND CLASSIFICATION	OVERALL FED SPEC SINGLE MATERIAL RESPONSE QQ-S-764
SPECIAL TEST FEATURES	SPECIAL QUALITY CONTROL TESTING
SECOND END RELATIONSHIP WITH FIRST END	IDENTICAL
PIN OVERALL LENGTH	INCHES NOMINAL 3.625
CENTER TO CENTER DISTANCE BETWEEN HOLES	INCHES NOMINAL 1.959
DISTANCE FROM CENTERLINE OF HOLE TO END OF PIN	INCHES NOMINAL 0.291

PICA SICA: P
PKG cat: 27A0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: 000
No intermediate container quantity specified (000)
Method of preservation: ZZ
Special requirements apply that are not represented by the code symbols; details are provided with the acquisition...
Clng drying: Z
Special requirements - See specific instructions or drawings provided.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: ZZ
Special requirement – See specific instructions or drawings provided.
PKG data source: P

PICA SICA: P
SPC MKG: 00
No special marking
Inter cont: 00
No requirement.
Lvl A: E
Packing shall be accomplished to meet the performance test requirements of ASTM D4169, Distribution Cycle 18,...
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.1000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0010
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: MIL-P23199, LEVEL B

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.