RESISTOR,VARIABLE,WIRE WOUND,NON

5905FSC

00NCB code

232-3638Item number

NIIN 00-232-3638

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNFC	RNSC
3290WH68-253	80294 BOURNS INSTRUMENTS INC	H	5	9	6	TX	3	B
230269-738	81413 BAE SYSTEMS INFORMATION AND ELECTRONIC SYSTEMS INTEGRATION INC. DBA BAE SYSTEMS	A	3	2	1	TX	3	D

RESISTANCE TOLERANCE PER SECTION IN PERCENT	SINGLE SECTION -5.0 TO 5.0
ACTUATOR TRAVEL CONTROL FEATURE	CLUTCH
SHAFT LENGTH	INCHES MAXIMUM 0.080
BODY LENGTH	INCHES NOMINAL 0.375
BODY WIDTH	INCHES NOMINAL 0.145
BODY HEIGHT	INCHES NOMINAL 0.390
SHAFT STYLE
ACTUATOR TYPE	SINGLE SHAFT
MAXIMUM STARTING TORQUE	INCH-OUNCES 5.00
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER	SINGLE SECTION 175.0
TERMINAL LOCATION	LOCATION NOT OTHERWISE SPECIFIED REAR END
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS	SINGLE SECTION -50.0 TO 50.0
POWER DISSIPATION RATING PER SECTION IN WATTS	FREE AIR SINGLE SECTION 1.0
TERMINAL TYPE AND QUANTITY	PIN 3
RELIABILITY INDICATOR	NOT ESTABLISHED
SHAFT DIAMETER	INCHES NOMINAL 0.075
SECTION QUANTITY	1
CENTER TO CENTER DISTANCE BETWEEN TERMINALS	INCHES NOMINAL 0.200
MOUNTING METHOD	TERMINAL
FEATURES PROVIDED	NONMETALLIC SHAFT
ELECTRICAL RESISTANCE PER SECTION	KILOHMS SINGLE SECTION 25.0
ROTARY ACTUATOR TRAVEL IN ANGULAR DEG	NOMINAL 9000.0
CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL	INCHES NOMINAL 0.100
BODY STYLE
TEST DATA DOCUMENT	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 81413-230269
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER	SINGLE SECTION 70.0

MOE rule	MOE CD	AMC	AMSC	Date assigned	PICA	PICA LOA	Auth collab
ZW01	ZW			01-NOV-05	ZW	81	ZW
DGX1	DS	1	L	01-NOV-25	GX	01	GX

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: A
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 41
Watervaporproof bag, heat sealed
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: FA
MIL-P-130, laminated and creped wrapping paper
Cush dun: 00
No requirement
THK: 0
Not applicable
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: D1
PPP-B-566 or PPP-B-676, folding or setup box.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.