RESISTOR,VARIABLE,WIRE WOUND,NON

5905FSC

01NCB code

024-0810Item number

NIIN 01-024-0810

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	J	SMS	EA	0.0000	$47.10	1	U	0	9B-----	$0.00	N
01-OCT-2026	DS	J	SMS	EA	0.0000	$47.10	1	U	0	-------	$0.00	I

SECTION QUANTITY	1
BODY STYLE
RELIABILITY INDICATOR	NOT ESTABLISHED
OVERALL LENGTH	INCHES NOMINAL 1.060
TERMINAL LENGTH	INCHES NOMINAL 0.200
OVERALL HEIGHT	INCHES NOMINAL 0.560
OVERALL WIDTH	INCHES NOMINAL 0.280
MOUNTING HOLE DIAMETER	INCHES MINIMUM 0.088
SHAFT DIAMETER	INCHES NOMINAL 0.100
SHAFT LENGTH	INCHES NOMINAL 0.060
BODY LENGTH	INCHES NOMINAL 1.000
BODY WIDTH	INCHES NOMINAL 0.280
BODY HEIGHT	INCHES NOMINAL 0.360
SHAFT STYLE
ACTUATOR TYPE	SINGLE SHAFT
CENTER TO CENTER DISTANCE BETWEEN TERMINALS	INCHES NOMINAL 0.500
FRAGILITY FACTOR	MODERATELY DELICATE
LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS	INCHES NOMINAL 0.830
MOUNTING FACILITY QUANTITY	2
MOUNTING METHOD	UNTHREADED HOLE(S) AND TERMINAL
CENTER TO CENTER DISTANCE BETWEEN TERMINAL ROWS	INCHES NOMINAL 0.200
ELECTRICAL RESISTANCE PER SECTION	OHMS SINGLE SECTION 100.0
CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL	INCHES NOMINAL 0.200
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER	SINGLE SECTION 105.0
TERMINAL LOCATION	LOCATION NOT OTHERWISE SPECIFIED LOWER ADJACENT SIDE TWO ROWS
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS	SINGLE SECTION -100.0 TO 100.0
POWER DISSIPATION RATING PER SECTION IN WATTS	FREE AIR SINGLE SECTION 0.5
RESISTANCE TOLERANCE PER SECTION IN PERCENT	SINGLE SECTION -10.0 TO 10.0
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER	SINGLE SECTION 25.0
TERMINAL TYPE AND QUANTITY	PIN 3

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: ZZ
Special requirements apply that are not represented by the code symbols; details are provided with the acquisition...
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: ZZ
Special requirement – See specific instructions or drawings provided
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: ZZ
Special requirement – See specific instructions or drawings provided.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: ZZ
Special requirement – See specific instructions or drawings provided.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0000
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: PRESERVATION AND PACKAGING

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.