RESISTOR,VARIABLE,WIRE WOUND,PRE

5905FSC

01NCB code

285-5488Item number

NIIN 01-285-5488

Identification

Effective date	Major organizational entity	Acquisition advice code	Source of supply	Unit of issue	Unit of measure quantity	Unit price	Quantity per unit pack	Controlled inventory item code	Shelf-life code	Management control	Net price	USC
01-OCT-2026	DN	J	SMS	EA	0.0000	$1,932.98	1	U	0	9B-----	$0.00	N
01-OCT-2026	DS	J	SMS	EA	0.0000	$1,932.98	1	U	0	-------	$0.00	I

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNSC	SADC
5839K70P004	97424 AMETEK INC DIV AEROSPACE AND DEFENSE	A	3	2	A	TX
5839K70P004	04454 SENSOR SYSTEMS, L.L.C. DBA SENSOR SYSTEMS LLC	A	C	1	3	ZZ		AC
4289	04454 SENSOR SYSTEMS, L.L.C. DBA SENSOR SYSTEMS LLC	A	5	9	5	TX	B
4289	10112 GENERAL DYNAMICS MOTION CONTROL LLC DIV GENERAL DYNAMICS OTS INC	A	5	2	5	TX
741-6508	19176 SERVO INSTRUMENT CORPORATION	A	5	2	A	TX

SECTION QUANTITY	2
BODY STYLE
RELIABILITY INDICATOR	NOT ESTABLISHED
PILOT DIAMETER	INCHES MINIMUM 0.9683 AND INCHES MAXIMUM 0.9688
PILOT LENGTH	INCHES MINIMUM 0.0570 AND INCHES MAXIMUM 0.0670
UNDERCUT DIAMETER	INCHES MAXIMUM 0.975
UNDERCUT WIDTH	INCHES MINIMUM 0.0570
BODY DIAMETER	INCHES MAXIMUM 1.125
SHAFT DIAMETER	INCHES MINIMUM 0.1246 AND INCHES MAXIMUM 0.1249
SHAFT LENGTH	INCHES MINIMUM 0.656 AND INCHES MAXIMUM 0.719
BODY LENGTH	INCHES MAXIMUM 1.250
MOUNTING LIP DIAMETER	INCHES MINIMUM 1.0570 AND INCHES MAXIMUM 1.0670
MOUNTING LIP DEPTH	INCHES MINIMUM 0.0570 AND INCHES MAXIMUM 0.0670
SHAFT STYLE
ACTUATOR TYPE	SINGLE SHAFT
MAXIMUM STARTING TORQUE	INCH-OUNCES 0.30
MAXIMUM RUNNING TORQUE	INCH-OUNCES 0.30
FRAGILITY FACTOR	MODERATELY RUGGED
END ITEM IDENTIFICATION	SPEC PROJ ERA
MOUNTING METHOD	CLAMP RING(S)
BEARING TYPE	SHAFT BEARING
CUBIC MEASURE	CUBIC INCHES 1.243
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER	ALL SECTIONS 125.0
TERMINAL LOCATION	LOCATION NOT OTHERWISE SPECIFIED RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS	ALL SECTIONS -20.0 TO 20.0
ACTUATOR TRAVEL CONTROL FEATURE	CLUTCH
TEST DATA DOCUMENT	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 97424-5839K70

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: A
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 41
Watervaporproof bag, heat sealed
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: CA
A-A-203, kraft wrapping paper
Cush dun: DA
A-A-1051, paperboard cushioning
THK: C
3/4 inch thick
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: DO
Any suitable fiber box included in this table may be used (see J.4.9.1).
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.1000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0030
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.