CAPACITOR,FIXED,PLASTIC DIELECTR

5910FSC

01NCB code

072-3764Item number

NIIN 01-072-3764

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNFC	RNSC
CQR29A1MA563G3P	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	2	2	3	TX	4	D
MIL-PRF-19978/13	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	4	1	E	ZZ
MILC19978-13	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	5	9	3	TX	1	B

BODY STYLE
RELIABILITY INDICATOR	ESTABLISHED
RELIABILITY FAILURE RATE LEVEL IN PERCENT	0.1000
TERMINAL LENGTH	INCHES MINIMUM 1.625
BODY DIAMETER	INCHES MAXIMUM 0.374
BODY LENGTH	INCHES NOMINAL 0.624
TERMINAL DIAMETER	INCHES NOMINAL 0.025
SCHEMATIC DIAGRAM DESIGNATOR
INTERNAL ELECTRICAL CONNECTION TYPE	EXTENDED FOIL
FEATURES PROVIDED	HERMETICALLY SEALED CASE
INSULATION RESISTANCE AT MAXIMUM OPERATING TEMP	MEGOHMS 25000.0
CAPACITANCE VALUE PER SECTION	MICROFARADS SINGLE SECTION 0.056
NONDERATED OPERATING TEMP	CELSIUS MINIMUM -65.0 AND CELSIUS MAXIMUM 85.0
NONDERATED CONTINUOUS VOLTAGE RATING AND TYPE PER SECTION	DC SINGLE SECTION 50.0
TOLERANCE RANGE PER SECTION	PERCENT SINGLE SECTION -2.00 TO 2.00
INSULATION RESISTANCE AT REFERENCE TEMP	MEGOHMS 100000.0
DISSIPATION FACTOR AT REFERENCE TEMP IN PERCENT	0.6000
TERMINAL SURFACE TREATMENT	SOLDER
DIELECTRIC MATERIAL	PLASTIC POLYETHYLENE TEREPHTHALATE (PET)(POLYESTER)
CASE INSULATION MATERIAL	PLASTIC
TEST DATA DOCUMENT	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-C-19978
TERMINAL TYPE AND QUANTITY	UNINSULATED WIRE LEAD 2
SPECIFICATION/STANDARD DATA	GOVERNMENT SPECIFICATION 81349--IL-C-19978 TO 13

PICA SICA: P
PKG cat: 60F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: A
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 10
Physical protection
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: 00
No requirement
Cush dun: NA
PPP-C-795, closed cell plastic cushioning; or A-A-3129, open cell plastic cushioning; or PPP-C-1797, polypropylene...
THK: C
3/4 inch thick
Unit cont: A1
Bags made of material conforming to MIL-P-130, or any bag authorized by MIL-DTL-117.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.1000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0030
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.