CAPACITOR,FIXED,ELECTROLYTIC

5910FSC

01NCB code

159-7153Item number

NIIN 01-159-7153

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNSC
M39018/04-2077M	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	2	2	E	TX
MIL-PRF-39018/4	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	4	1	E	ZZ
M39018/04-1077	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	5	9	6	TX	B
MIL-C-39018/4	81349 MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M	A	5	9	E	TX	B

BODY STYLE
RELIABILITY INDICATOR	ESTABLISHED
RELIABILITY FAILURE RATE LEVEL IN PERCENT	1.0000
TERMINAL LENGTH	INCHES NOMINAL 0.281
BODY DIAMETER	INCHES NOMINAL 2.032
BODY LENGTH	INCHES NOMINAL 5.141
CENTER TO CENTER DISTANCE BETWEEN TERMINALS PARALLEL TO DIAMETER	INCHES NOMINAL 0.875
TERMINAL DIAMETER	INCHES NOMINAL 0.190
SCHEMATIC DIAGRAM DESIGNATOR
ANODE TYPE	PLAIN FOIL
IMPEDANCE AT MINIMUM OPERATING TEMP IN OHMS	0.19
ELECTRICAL POLARIZATION	POLARIZED
CAPACITANCE VALUE PER SECTION	MICROFARADS SINGLE SECTION 26000.000
NONDERATED OPERATING TEMP	CELSIUS MINIMUM -55.0 AND CELSIUS MAXIMUM 85.0
DC LEAKAGE AT MAXIMUM OPERATING TEMP	MILLIAMPERES 5.52
NONDERATED CONTINUOUS VOLTAGE RATING AND TYPE PER SECTION	DC SINGLE SECTION 20.0
TOLERANCE RANGE PER SECTION	PERCENT SINGLE SECTION -10.00 TO 50.00
CAPACITIVE ELECTRODE MATERIAL	ALUMINUM
EQUIVALENT SERIES RESISTANCE AT REFERENCE TEMP IN OHMS	0.015
DC LEAKAGE AT REFERENCE TEMP	MILLIAMPERES 0.920
CASE INSULATION MATERIAL	PLASTIC
TEST DATA DOCUMENT	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-C-39018
TERMINAL TYPE AND QUANTITY	THREADED HOLE 2
SPECIFICATION/STANDARD DATA	GOVERNMENT SPECIFICATION 81349--IL-C-39018 TO 4

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
TOS: A
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: 41
Watervaporproof bag, heat sealed
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: 00
No requirement
Cush dun: NA
PPP-C-795, closed cell plastic cushioning; or A-A-3129, open cell plastic cushioning; or PPP-C-1797, polypropylene...
THK: C
3/4 inch thick
Unit cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: DO
Any suitable fiber box included in this table may be used (see J.4.9.1).
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Unit pack weight: 0.6000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0310
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.