MICROCIRCUIT,MEMORY

5962FSC

01NCB code

030-3151Item number

NIIN 01-030-3151

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNFC	RNSC
R261134-1	34371 RENESAS ELECTRONICS AMERICA INC	A	5	9	5	TX	1	B
HPROM1-0512-2	34371 RENESAS ELECTRONICS AMERICA INC	A	5	9	3	TX	1	B
R261134-1	04071 RAYTHEON COMPANY	A	3	2	1	TX	1	D
ROM/PROM FAMILY 018	16236 DLA WEAPONS SUPPORT (COLUMBUS) DBA DLA VENDOR ITEM DRAWING (VID) DIV DOCUMENT STANDARDIZATION DIVISION (VA)	A	5	1	5	TX

BODY LENGTH	INCHES MINIMUM 1.230 AND INCHES MAXIMUM 1.280
BODY WIDTH	INCHES MINIMUM 0.520 AND INCHES MAXIMUM 0.560
BODY HEIGHT	INCHES MINIMUM 0.160 AND INCHES MAXIMUM 0.200
OPERATING TEMP RANGE	CELSIUS -55.0 TO 125.0
STORAGE TEMP RANGE	CELSIUS -65.0 TO 150.0
END ITEM IDENTIFICATION	DIRECTIONAL FINDER SET FSCM 04071
FEATURES PROVIDED	HERMETICALLY SEALED AND MONOLITHIC AND NEGATIVE OUTPUTS AND POSITIVE OUTPUTS AND W/ENABLE AND EXPANDABLE AND W/BUFFERED OUTPUT AND WIRE-OR OUTPUTS AND PROGRAMMABLE AND PROGRAMMED AND W/DECODED OUTPUT
INCLOSURE MATERIAL	CERAMIC AND GLASS
INCLOSURE CONFIGURATION	DUAL-IN-LINE
OUTPUT LOGIC FORM	TRANSISTOR-TRANSISTOR LOGIC
INPUT CIRCUIT PATTERN	8 INPUT
TERMINAL SURFACE TREATMENT	SOLDER
VOLTAGE RATING AND TYPE PER CHARACTERISTIC	VOLTS MINIMUM POWER SOURCE -1.5 AND VOLTS MAXIMUM POWER SOURCE 5.5
TIME RATING PER CHACTERISTIC	NANOSECONDS MINIMUM PROPAGATION DELAY TIME, LOW TO HIGH LEVEL OUTPUT 25.00 AND NANOSECONDS MAXIMUM PROPAGATION DELAY TIME, LOW TO HIGH LEVEL OUTPUT 75.00
MEMORY DEVICE TYPE	ROM
MEMORY CAPACITY	UNKNOWN
TEST DATA DOCUMENT	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 04071-R261134
TERMINAL TYPE AND QUANTITY	PRINTED CIRCUIT 24

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: GX
Preserve by Method 41 using an approved ESD control program (see 5.2.4.1.1) as follows: Items subject to damage by...
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: ZZ
Special requirement – See specific instructions or drawings provided.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Lvl c: U
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping...
Unit pack weight: 0.0000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0040
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.