MICROCIRCUIT,MEMORY

5962FSC

01NCB code

040-4354Item number

NIIN 01-040-4354

Identification

Part number	CAGE	CAGE status	RNCC	RNVC	Document availability code	RNAAC	RNFC	RNSC
6306-1J	50364 MMI/AMD	H	5	9	3	TX	4	B
MM6306-1J	50364 MMI/AMD	H	5	9	3	TX	4	B
278539-37	50364 MMI/AMD	H	5	9	5	TX	4	B
278539-37	60854 LOCKHEED MARTIN CORPORATION DIV LOCKHEED MARTIN INFORMATION SYSTEMS & GLOBAL SOLUTIONS	A	3	2	1	TX
278539-37	11530 LOCKHEED MARTIN CORPORATION DIV LOCKHEED MARTIN INFORMATION SYSTEMS & GLOBAL SOLUTIONS	A	5	9	1	TX	4	B
ROM/PROM FAMILY 008	16236 DLA WEAPONS SUPPORT (COLUMBUS) DBA DLA VENDOR ITEM DRAWING (VID) DIV DOCUMENT STANDARDIZATION DIVISION (VA)	A	5	1	5	TX

BODY LENGTH	INCHES MINIMUM 0.750 AND INCHES MAXIMUM 0.795
BODY WIDTH	INCHES MINIMUM 0.245 AND INCHES MAXIMUM 0.300
BODY HEIGHT	INCHES MINIMUM 0.120 AND INCHES MAXIMUM 0.195
MAXIMUM POWER DISSIPATION RATING	MILLIWATTS 625.0
OPERATING TEMP RANGE	CELSIUS 0.0 TO 75.0
STORAGE TEMP RANGE	CELSIUS -65.0 TO 150.0
END ITEM IDENTIFICATION	CHEYENNE AIRCRAFT MODEL 427M
FEATURES PROVIDED	BIPOLAR AND HERMETICALLY SEALED AND HIGH SPEED AND MONOLITHIC AND POSITIVE OUTPUTS AND PROGRAMMABLE AND PROGRAMMED AND W/BUFFERED OUTPUT AND W/DECODED OUTPUT AND W/DISABLE AND W/ENABLE AND W/STORAGE AND 3-STATE OUTPUT
INCLOSURE MATERIAL	CERAMIC AND GLASS
INCLOSURE CONFIGURATION	DUAL-IN-LINE
OUTPUT LOGIC FORM	TRANSISTOR-TRANSISTOR LOGIC
INPUT CIRCUIT PATTERN	10 INPUT
CASE OUTLINE SOURCE AND DESIGNATOR	JOINT ELECTRON DEVICE ENGINEERING COUNCIL -0-001-AG
TERMINAL SURFACE TREATMENT	SOLDER
VOLTAGE RATING AND TYPE PER CHARACTERISTIC	VOLTS MAXIMUM POWER SOURCE 5.5
TIME RATING PER CHACTERISTIC	NANOSECONDS MAXIMUM PROPAGATION DELAY TIME, LOW TO HIGH LEVEL OUTPUT 30.00 AND NANOSECONDS MAXIMUM PROPAGATION DELAY TIME, HIGH TO LOW LEVEL OUTPUT 30.00
MEMORY DEVICE TYPE	ROM
MEMORY CAPACITY	UNKNOWN
TEST DATA DOCUMENT	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 11530-278539
TERMINAL TYPE AND QUANTITY	PRINTED CIRCUIT 16

MOE rule	MOE CD	AMC	AMSC	Date assigned	PICA	PICA LOA	Auth collab	Supp collab	Fmr MOE rl
YA01	YA			01-OCT-00	YA	81	YA
DGX1	DS	3	L	01-AUG-06	GX	01	GX	TX	DTX1

PICA SICA: P
PKG cat: 69F0
Unpackaged weight: 0.0000
Unpackaged width: 0.000
Unpackaged length: 0.000
Unpackaged height: 0.000
Intermediate container qty: AAA
Quantity set by MIL-STD-2073-1E B.5: up to 100 unit packs, a maximum net load of 40 pounds, and a maximum of 1.5...
Method of preservation: GX
Preserve by Method 41 using an approved ESD control program (see 5.2.4.1.1) as follows: Items subject to damage by...
Clng drying: 1
Any suitable process that is not injurious to the item.
Pres mat: 00
No requirement
Wrap mat: ZZ
Special requirements – see specific instructions or drawings provided
Cush dun: ZZ
Special requirements.
THK: C
3/4 inch thick
Unit cont: ZZ
Special requirement – See specific instructions or drawings provided.
PKG data source: P

PICA SICA: P
SPC MKG: ZZ
Special requirements
Inter cont: D3
PPP-B-566, PPP-B-676, or ASTM D5118/D5118M, folding, setup or fiberboard box.
Lvl A: Q
Packing shall be accomplished in accordance with table C.II for the packing level specified.
Lvl b: Q
Packing shall be accomplished in accordance with table C-II for the packing level specified.
Lvl c: U
Items or packages that require packing for acceptance by the carrier shall be packed in exterior type shipping...
Unit pack weight: 0.1000
UP SZ MAXB: 0.00000
UP SZ MAXL: 0.00000
UP SZ MAXH: 0.00000
Unit pack cube: 0.0030
OPI: M
All packaging data is mandatory for compliance and no substitutions are permitted.
Supplemental instructions: UNIT PACKAGE MARKING REQUI

Your request goes to A-DEFENSE, a US Defense supplier in Texas, who will reply by email.